Oct. 1 LADEE Trajectory Update: LADEE leaves Earth

 

10_1_post_ECI

LADEE on 10-1-2013 16:56 UTC (Earth-Centered Inertial View)

10_1_post_top

LADEE on 10-1-2013 16:56 UTC (Rotating Coordinate Frame)

10_1_post_rotating

LADEE on 10-1-2013 16:56 UTC (Top View)

 

 

LADEE passed perigee this morning near 4 AM PDT and is now headed for the Moon.  Currently the spacecraft is above GEO, with the TCM-1 maneuver coming at 3 PM PDT today (1 Oct. 2013)

Sep 30 LADEE Trajectory Update

LADEE on 9-30-2013 18:05 UTC (Rotating Coordinate Frame)

LADEE on 9-30-2013 18:56 UTC (Rotating Coordinate Frame)

sep30_ECI

LADEE on 9-30-2013 18:56 UTC (Earth-Centered Inertial Coordinate Frame)

 

sep_30_top

LADEE on 9-30-2013 18:56 UTC (Top View)

 

 

Next Maneuver:  TCM-1 on 1 Oct. 2013 22:00:00 UTC (11 hrs after Perigee 3).

LADEE turns the corner, bound for last perigee (9-28-13)

On Sep. 28 2013 05:33 UTC, LADEE is coming out of its last apogee and at an altitude of 214,000 km.

ECI_928

LADEE on 9-28-2013 5:46 UTC

top_927

LADEE on 9-28-2013 5:46 UTC (Top View)

 

 

 

Perigee occurs on 1 Oct near 11:00 UTC.  A final small midcourse maneuver will take place at 1 Oct 2013, 22:00 UTC.  This 0.9 m/sec maneuver will precisely target insertion parameters for the 6 Oct. 2013 10:57 UTC LOI-1 maneuver.  LOI-1 is designed to place the spacecraft into a 24 hr orbit, with a periselene altitude of 590 km [correction:  previously I said 750 km, this isn’t quite right.  For LADEE we aren’t capturing right at periselene, like orbital mechanics would recommend.  Instead we burn off periselene just a bit.  We wait until 5 minutes past we come out from behind the Moon, and start our burn.  This ends up being roughly 5.5 minutes after periselene. This allows the Deep Space Network to get a lock on us and telemetry to start flowing before the burn starts.  So the altitude at the end of this burn is at about 750 km, but the actual periselene altitude is closer to 590 km].  After 3 revolutions in this orbit, 3rd-body Earth gravitational perturbations will have lowered periselene to an altitude of 250 km (by design).  At this point, LOI-2 will be performed on 9 Oct 2013 10:37 UTC ( to place LADEE into a 4 hr orbit (also with a 250 km periselene altitude).  LADEE will spend 3 days in this orbit until LOI-3 (12 Oct 2013 10:37 UTC), which circularizes the orbit at 250 km.  LADEE will spend 30 days in this “commissioning orbit”, and will also perform tests using the laser communications experiment (LLCD). The timing and magnitudes of the maneuvers leading to the commissioning orbit are given below.

 

 

 

Rotating_927

LADEE on 9-28-2013 5:48 (Earth-Moon rotating frame)

Executed Maneuvers:

AM1 11 Sep 2013 23:00:00.000 9.34 m/sec

PM1 13 Sep 2013 16:36:08.000 16.96 m/sec

PM2 21 Sep 2013 11:53:19.000 17.492 m/sec

Planned Maneuvers

TCM1 01 Oct 2013 22:00:00.000 0.9 m/sec

LOI1 06 Oct 2013 10:57:00.210 329.86 m/sec

LAM1 07 Oct 2013 22:51:32.205 0 m/sec (error corrections for LOI-1)

LOI2 09 Oct 2013 10:37:55.651 295.99 m/sec

LOI3 12 Oct 2013 10:37:34.993 238.56 m/sec

LADEE Moon-Bound after PM2

Here’s a quick LADEE update for Sept. 22, 2013.  The LADEE team performed a second Perigee maneuver yesterday (21 Sep. 2013, 11:53 UTC) to raise LADEE’s orbit to have a period of 10 days, and to set up the spacecraft for Lunar capture on Oct. 6.  LADEE’s path to this point is shown in dotted lines, while the upcoming trajectory is shown as solid.  Note that LADEE is now in phasing loop 3, and will continue around a full orbit that will conclude on October 1st.   LADEE will then begin the final portion of its trajectory, the 5 day trip to the Moon which concludes on Oct 6 with Lunar Orbit Insertion burn LOI-1.  No further deterministic maneuvers are required (only a small TCM to correct out statistical errors from PM2) before the LOI phase begins.  So even though LADEE has a full Earth orbit left, it is Moon-bound.  LADEE is still in an elliptical orbit of the Earth, but at the next apogee LADEE will encounter the Moon.

sep_22_now_rot

LADEE today in Earth-Moon Rotating Coordinate Frame

sep_22_now_eci

LADEE today in Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

 

Phasing Loops and the LADEE trajectory

Many people have asked about LADEE’s trajectory, which uses 3 and a half “phasing loops” to get to the Moon. On one of my other postings, a reader asked if phasing loops saved delta-v on the trans-lunar injection (TLI) burn. The answer is no. The cost (in delta-v) to get to a lunar transfer from a specific injection orbit (for example the 6.4 day orbit LADEE currently is in) is the same if you go direct as it is if you go around a few times first.

The savings come elsewhere, in particular with the cost of correcting for errors from the launch vehicle (rocket).

There are four important reasons why phasing loops are being used for LADEE.

1. Mass

The Minotaur V couldn’t throw the whole mass of LADEE all the way to Lunar Injection.

2. Launch Dispersions

Let me borrow from my answer in the comments section on a previous post:

The Minotaur V, which is a stack of 5 solids, isn’t considered to be a particularly precise rocket. In other words, if we were to ask for a 6.3 day orbit, we might get a 5 day orbit, or we might get an 8 day orbit. In a direct injection trajectory (such as the 3-day missions used by Apollo), injection errors can only be corrected out after good amount of tracking can be done (~ 24 hrs normally) to determine the orbit (OD, or “Orbit Determination”). However, as the spacecraft gets further and further away from the Earth, the cost of correcting out launch errors gets larger as well. Often times, by the time enough tracking data can be gathered, the cost of correcting out any launch errors can be 5-10 times the actual size of the error. So a 5 m/sec error would take 25 m/sec to correct, etc.

If, instead of using a direct approach, you use phasing loops the cost is a lot closer to 1:1 (i.e. a 5 m/sec error in launch costs 5 m/sec to correct, or can even save you fuel). It’s not a pure 1:1 ratio, because there is a timing aspect as well, but in terms of the energy of the orbits, it is 1:1.

Assume that you’re going to launch to a 6.4 day orbit and that you’ll then transfer to an 7.6 day orbit, and then a 10 day orbit, and then spend 5 days getting to the Moon (total of 29 days). The cost of transferring to the 5-day lunar transfer from the 6.4 day starting orbit is always the same. Now say that your rocket doesn’t give you exactly what you want, and instead of a 6.4 day orbit, you are inserted into a 7 day orbit. Instead of doing a TCM to correct out that error, you simply replan your trajectory profile. You spend 7 days in the first orbit, but instead of transferring to a 7.6 day orbit, your first maneuver is zero, and you stay in the 7 day orbit for 2 days. So your first rev is 7 days, second rev is 7 days, and then you transfer to a 10 day orbit, and take 5 more to get to the Moon (still 29).

Same thing if you are launched to a 5 day orbit. The second orbit can be 9 days, the third 10, and 5 days to the Moon (29 days total again).

You get the picture.

The total delta-v to get to the Moon doesn’t really change, but your orbit profile is flexible to large dispersions in your injection.

Phasing loops have been used on many other missions (Clementine and WMAP are 2 good examples). I designed the phasing loops on LADEE to accommodate the Minotaur V dispersions. The LADEE spacecraft barely had enough fuel to do its science mission, and the choice of phasing loops allowed the mission to accommodate the Minotaur V dispersions, at the cost of some extra time in cislunar space. The operations costs are not free (of course), but if you can’t fit on the rocket, sometimes you don’t have a mission.

[Funny thing is that although the Minotaur V is “supposed” to have large dispersions, the fact is that the launch last Friday (Sept 7, 2013) was just about perfect. We got almost precisely the nominal trajectory, in what probably is the most precise injection a Minotaur rocket has ever done. Had we known in advance that we could have gotten such an injection, we probably would have gone direct.]

So here are a few examples of how phasing loops allow you flexibility. As stated previously, LADEE was launched into a 6.4 day orbit. However, let’s say LADEE got into a 5 Day orbit instead:

If LADEE had been launched into a 5 day orbit (green), we then could have raised the 2nd orbit to have a 9.5 day period (blue), and the third to have a 9.8 day period purple and then done our normal 5 day transfer to the Moon.  The two pictures below tell the story.  On the left the orbit is shown in an Earth-Moon Rotating coordinate system.  The Earth is in the middle, and the Moon is stationary from the top.  Imagine that you’re way above the Earth-Moon system, and that you are slowly rotating at exactly the same rate as the Moon goes around the Earth.  On the right is the normal view, an Earth-centered inertial frame.

5 Day Insertion Orbit, Earth-Moon Rotating Frame

5 Day Insertion Orbit, Earth-Moon Rotating Coordinate Frame

5 Day Insertion Orbit - Earth Centered Inertial Coordinate Frame.

5 Day Insertion Orbit, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

If LADEE had been launched into a 6 day orbit (green), we then could have raised the 2nd orbit to have an 8.3 day period (blue), and the third to have a 9.9 day period purple and then done our normal 5 day transfer to the Moon.

6 Day Insertion Orbit, Rotating Coordinate Frame

6 Day Insertion Orbit, Earth-Moon Rotating Coordinate Frame

6 Day Insertion Orbit, Inertial Coordinate Frame

6 Day Insertion Orbit, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

If LADEE had been launched into a 7 day orbit (green), we then could have raised the 2nd orbit to have an 8.1 day period (blue), and the third to have a 9 day period purple and then done our normal 5 day transfer to the Moon.

7 Day Insertion Orbit, Earth-Moon Rotating Frame

7 Day Insertion Orbit, Earth-Moon Rotating Coordinate Frame

7 Day Insertion Orbit, Inertial Frame

7 Day Insertion Orbit, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

If LADEE had been launched into an 8 day orbit (green), we then could have raised the 2nd orbit to have an 8.4 day period (blue), lowered the third to have a 7.7 day period purple and then done our normal 5 day transfer to the Moon.  The 8 day orbit and above starts to cost more energy, because you have to lower the 2nd orbit and then raise it back up for the third.  So in this case, while the rocket would have placed us in a higher orbit than we wanted (and thus you’d think it might save us energy) we end up having to pay a bit extra to get the timing right.

 

8 Day Insertion Orbit, Rotating Frame

8 Day Insertion Orbit, Earth-Moon Rotating Coordinate Frame

8 Day Insertion Orbit, Inertial Frame

8 Day Insertion Orbit, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

Note here that all the examples I show have us keeping the time of the third perigee mostly constant, along with the time of flight between that perigee and the Moon constant at 5 days.  This comes from the fact that once we’ve launched and the Minotaur Stage 5 has fired, our line of apsides (between apogee and perigee) is mostly fixed in space (actually it was fixed before launch for optimization purposes, but that’s another topic) and we are now locked into getting at the Moon when the Moon is at the same latitude as our apogee.

3. Widening the Launch Window

Another thing phasing loops give you are a wider launch window.  With the argument of perigee (and thus the line of apsides) fixed before launch, we are fixed to arrive at the Moon when it as a specific latitude (same as our apogee).  Given that, a direct launch would have only had a very short launch period if you assume that you’re always launching with the same energy from the upper stage.  Phasing loops allow you to widen the window up to 5 days.  In the case of LADEE, we actually launched on the first day of the launch period (on the first second of the launch window) but we were lucky.  We’ll take the luck, but we didn’t plan for it.  Instead, we had a 5 day window.

On the first day of the launch window (Sep. 6, 2013), our first orbit would be 6.4 days, the 2nd 7.95, the third 9.95 and then about 5 days to the Moon.

Day 1 Rotating

Day 1 of Launch period, Earth-Moon Rotating Coordinate Frame

Day 1 ECI

Day 1 of Launch Period, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

On the second day of the launch window (Sep. 7, 2013), our first orbit would be 6.33 days [Note: the rocket is always launching us to the same orbit, but the Moon’s gravity alters our orbit a bit, so the first rev doesn’t always have the same period] , the 2nd 7.00, the third 9.95 and then about 5 days to the Moon.

day 2 ECI

Day 2 of Launch Period, Earth-Centered Inertial Coordinate Frame

day 2 rotating

Day 2 of Launch Period , Earth-Moon rotating Coordinate Frame

 

 

 

 

 

 

 

 

 

 

On the third day of the launch window (Sep. 8, 2013), our first orbit would be 6.24 days, the 2nd 6.32, the third 9.55 and then about 5 days to the Moon.

day 3 rotating

Day 3 of Launch Period, Earth-Moon Rotating Coordinate Frame

Day 3 ECI

Day 3 of Launch Period, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

 

On the fourth day of the launch window (Sep. 9, 2013), our first orbit would be 6.19 days, the 2nd 6.27, the third 8.82 and then about 5 days to the Moon.

day 4 Rotating

Day 4 of Launch Period, Earth-Moon Rotating Coordinate Frame

Day 4 ECI

Day 4 of Launch Period, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

 

The last day of the launch window (Sep. 10, 2013), our first orbit would be 6.16 days, the 2nd 6.32, the third 7.95 and then about 5 days to the Moon.

 

Day 5 Rotating

Day 5 of Launch Period, Earth-Moon Rotating Coordinate Frame

Day 5 ECI

Day 5 of Launch Period, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

Why does the launch period stop?  Look at the rotating frame picture in each of the examples.  Think of the picture in terms of quadrants, with the first quadrant being in the upper right, second in the lower right, third in the lower left, and 4th in the upper left.  Any loop in the first quadrant gets to apogee with the Moon in front of it.  This is fine, because the gravity of the Moon will give us some extra velocity at apogee, and will raise our subsequent perigee altitude. The closer we are to the Earth-Moon line (the vertical white line in the rotating frame picture), the more boost we get from the Moon.  The further away we are from the Moon, the less boost we get.  Going into the 4th quadrant is bad, because if we get in front of the Moon at apogee, then the Moon’s gravity slows us down, and drives the perigee altitude into the Earth.  In the 2nd quadrant we get slight gravitational lowering at perigee, and the 3rd we get slight gravitational raising.  If you watch the sequence through the launch period, you see that each day the first loop clocks further (clockwise) to the right, closer to the 2nd quadrant.  We have to launch to get our orbital plane to match the Moon’s on arrival, and also have to make this happen when the Moon has the same latitude as our apogee.

This is all important for the trajectory planning of LADEE, because when you launch off a rocket from the Earth, your insertion perigee is usually low (200 km).  You don’t want to come back at this altitude the next time around.  So we launch when the Moon will raise us (without requiring a maneuver at apogee, which we could also do, but we’d rather not require a maneuver at the first apogee to keep the spacecraft from hitting the Earth).  So as long as our first loop stays within the first quadrant in the rotating frame, we’re OK.  This gives us a 4-5 day launch window (some times we lose the first day if we decide that potential launch dispersions will throw too many statistical cases into the 4th quadrant.)

4. Flexibility after launch

The phasing loop plan is also very robust in the face of missed maneuvers.  A missed PM1, for example, can easily be accommodated by modified PM2 and PM3 maneuvers and still get to the Moon at the same time.  A missed PM2 is can be accommodated by waiting another month in orbit, and achieving LOI-1 in November.  The ability of the plan to easily be modified in the face of contingencies is another strong feature of the phasing orbit approach.

In the pictures below, we see what happens with a missed PM1.  The spacecraft stays in 6.4 day orbit for a second rev, and then raises to a 11.25 day orbit with a 41 m/sec maneuver.  At the final perigee (Pf or PM3) we execute a -8 m/sec maneuver to bring apogee down to Lunar altitude.

missed PM1 Rotating

Post Launch Missed PM1 Trajectory, Earth-Moon Rotating Coordinate Frame

missed PM1 ECI

Post Launch Missed PM1 Trajectory, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

 

The plan is also robust to a missed PM2 maneuver.  This profile would require LADEE to wait an extra month in Earth orbit.  The gray orbits indicate the first month.  We show the trajectory starting after PM1 moving towards PM2.  Once PM2 is missed, the spacecraft spends 2 more revs in the grey (moving through the 4th quadrant) and then the approach pattern starts again.

missed PM2 rotating

Post Launch Missed PM2 Trajectory, Earth-Moon Rotating Coordinate Frame

missed PM2 eci

Post Launch Missed PM2 Trajectory, Earth-Centered Inertial Coordinate Frame

 

 

 

 

 

 

 

 

 

 

 

Phasing loops offer several advantages to the mission planner.  At the expense of longer operation costs, phasing loops have offer a reduced TCM budget in the face of large launch dispersions, expanded launch windows, and over-all robustness to contingencies.

Where is LADEE Now, and where is it going?

After the successful launch of LADEE last Friday:

NASA’s LADEE Page

you may be wondering where the LADEE spacecraft is now, and what are the next steps on the trajectory. So here we are, LADEE on Sept 11, 9 AM PDT:

LADEE on Sept 11, 2013

LADEE on Sept 11, 2013

Note the upcoming phasing loops (dotted) and the Moon to the upper right. Of course this is a 3-D picture, and you can get a better feel for where the Moon is now here:

LADEE on Sept. 11, 2013 with Moon (side view)

LADEE on Sept. 11, 2013 with Moon (side view)

We (LADEE Flight dynamics) often like to look at the lunar trajectories in an Earth-Moon rotating frame. The Earth is at the middle, the Moon at the top:

LADEE on Sept. 11 (Earth-Moon Rotating Coordinate frame)

LADEE on Sept. 11 (Earth-Moon Rotating Coordinate frame)

On Sep. 13, 2013, LADEE will reach first perigee:

LADEE at first perigee

LADEE at first perigee

The first orbit-raising maneuver (after the test maneuver on Sep. 11) will occur here. This maneuver is called Perigee Maneuver 1 (PM1) and will raise LADEE’s orbit and change the orbit period from 6.44 days to 7.6 days. This brings us to perigee 2 on Sep. 21, 2013:

Perigee 2

Perigee 2

From here we perform PM2, and raise the orbit period to 10 days. We get back to perigee 3 on Oct. 1, 2013:

Perigee 3

Perigee 3

We have no nominal burn at Perigee 3 (although we may perform a trajectory correction maneuver there, and one more 36 hrs later for our final precise targeting to our Lunar arrival conditions).

Finally, we take a 5-day transfer to the Moon, where we arrive on Oct. 6, 2013 for our first Lunar Orbit Insertion burn (LOI-1). We use 3 maneuvers for Lunar capture, which we will describe in another post.

Lunar Approach

Lunar Approach

Here’s a few more pictures of the complete LADEE trajectory:

Complete LADEE Cislunar Trajectory, Earth Centered Inertial coordinate frame.

Complete LADEE Trajectory, Earth Centered Inertial coordinate frame.

Complete LADEE Cislunar Transfer trajectory, Earth-Moon Rotating Coordinate Frame

Complete Lunar Transfer trajectory, Earth-Moon Rotating Coordinate Frame